Engineering Data

Unlike ordinary direct-acting relief valves, Fulflo guided piston valves are less responsive to transient pressure surges, thereby eliminating the tendency to pound, squeal, or chatter. Quiet, stable, efficient performance is assured in both load regulation and system protection applications.

Fulflo valves operate effectively with all types of liquids in the full range of viscosities including hydraulic oils, water, solvents, and chemicals.

Fulflo valves are not designed to be positive shut off valves and will pass a minimal amount of leakage before the set pressure.

Fulflo valves are not designed for use with air, gas, or steam.

Since the Fulflo relief valve is a flow-modulating device, pressure-flow characteristics are completely different from spring-loaded poppet or ball check valves.

Both types remain substantially tight up to cracking pressure. When this pressure is exceeded, the “conventional” valve pops open with a pressure drop at very low flow and an exponential pressure rise as the flow increases.

In contrast, the Fulflo valve causes a pressure rise, over-pressure, as soon as flow starts; pressure increases almost proportionally with the flow. Fulflo valves are carefully designed to minimize this over-pressure.

Both pressures are important in sizing a valve. Cracking pressure must be selected high enough to permit system operation at its maximum rated pressure and flow. Over-pressure is limited by the system’s capability to withstand the additional pressure and the motor’s ability to sustain the pump output at the increased pressure for the required time interval.

The over-pressure to produce a certain flow is a function of valve size and spring constant, and can be determined with the aid of the performance charts given for the different valve sizes. The valve performance charts are based on tests made with oil of 150 SSU viscosity at 100˚F and may be used with reasonable accuracy within the conventional range of oil viscosities from 30 to 500 SSU. For operation with high viscosity fluids, consult Fulflo’s engineering department.

In sizing a valve, the first attempt should be to select a valve equal in size to the pipe to which it is connected. A larger or smaller valve may be used to suit individual requirements, depending on the permissible amount of over-pressure. Assume we have selected a 3/4” valve for 17 gpm, flow and a cracking pressure of 325 psi. By referring to the valve’s spring pressure range chart, we find that we may use either a “YS” or a “ZS” spring.

Assuming a “YS” spring, draw a line horizontally at 17 gpm in the 3/4” valve chart, to intersect the slanted line marked “YS” and drop a vertical line to the over-pressure scale to read an over-pressure of 44 psi. The 17 gpm will be discharged at a pressure of 325 + 44, or 369, psi. The percentage of over-pressure would be 44/325 x 100, or 13.5%.

If a “ZS” spring is used, extend the horizontal line to the “ZS” slope and the over-pressure is 70 psi. The pressure to pass 17 gpm would be 325 + 70, or 395, psi and the over-pressure would be 21.5%. If the over-pressure is higher than desired for the particular application, the procedure may be repeated for the next larger size valve.

In some cases, maximum flow through a valve at a given pressure is specified. To determine the cracking pressure, assume a 3/4” valve is to pass 12 gpm at 50 psi. A horizontal line drawn from the 12 gpm capacity to the intersection with the “WS” spring line results in an over-pressure of 14 psi, therefore the cracking pressure must be 50 – 14, or 36, psi, and the percentage of over-pressure of only 9 psi, but the cracking pressure would be 14/36 x 100, or 38.8%. The use of a “US” spring would produce an over-pressure of only 9 psi, but the cracking pressure would then be 50 – 9, or 41, psi, which would exceed the rating of the “US” spring.

For sizing valves for higher viscosity than 500 SSU, the following formula is used:

Assume we have the following application,
gpm = 10
Viscosity = 12,000 SSU
Normally for 10 gpm flow a 1/2” valve would be used.
The orifice area chart below gives the area of a 1/2” valve as .305.

2.99 x .305=.9120 area needed to pass 10 gpm. Again referring to the orifice area chart, we find that the area of the 1¹/⁴” valve is 1.224. Therefore a 1¹/⁴” valve would be used. To find the over-pressure, refer to the performance chart for a 1¹/⁴” valve.

Performance charts based on actual test results are available on request. For additional information contact Fulflo’s engineering department.